🔥 Heat Update Due to the extreme heat, we and our transport partners (such as PostNL) are temporarily adjusting our operations. As a result, the processing and delivery of orders may take slightly longer than usual. More information.
✔ Very good flowability and self-deaeration
✔ Low Shore A hardness (approx. 25)
✔ Excellent tear strength
✔ High elongation and flexibility
✔ Excellent chemical resistance to attack by polyester and polyurethane resins, significantly extending mould life
✔ Very good flowability and self-deaeration
✔ Low Shore A hardness (approximately 25)
✔ Excellent tear strength
✔ High elongation and flexibility
✔ Excellent chemical resistance to attack by polyester and polyurethane resins, mould life is significantly extended
✔ High-quality silicone from Wacker
✔ Fast and non-shrink curing at room temperature
✔Shore A 43
✔ Transparent
✔High tear strength
✔ Food safe (FDA)
✔ Excellent resistance to casting resins
✔ Very suitable for clear casting resins
✔ready-to-use, one-component system
✔low module
✔excellent primerless adhesion to many substrates
✔no use of organotin catalysts
✔ Flexible at low (-40 °C) and high temperatures (+180 °C)
✔Flowable
✔Low viscosity
✔Solvent-based
✔ Provides excellent adhesion onto various substrates.
✔ For addition curing silicone
✔ Solvent based
✔ Various application methods (e.g. coating, dipping, brushing, spraying)
✔ Further dilution in organic solvents possible
✔ Suitable for the production of reusable silicone vacuum bags.
✔ Fast curing at room temperature
✔ No chemical shrinkage
✔ Resistance to epoxy resins
✔ Resistance to polyester
✔ Two components 1:1
✔ Blue / Transparent
✔ Recommended service temperature from -45 °C to +230 °C
✔ max. recommended short term peak temperature exposure 250°C
✔ non-thixotropic
✔ Flowable
✔ Heat resistant
✔ Low viscosity
✔ One-component
✔ Solvent-free
✔ Food grade
✔ One component acid-based curing system.
✔ Self-leveling.
✔ Excellent adhesion on various surfaces
✔ Colorless transparent
✔ Good mechanical properties
✔ Heat resistant
✔ Resistant to weather influences and aging
✔ Permeable to gas and water vapor
✔ One component acid-based curing system.
✔ Self-leveling.
✔ Excellent adhesion on various surfaces
✔ Colorless transparent or Black
✔ Good mechanical properties
✔ Heat resistant
✔ Resistant to weather influences and aging
✔ Permeable to gas and water vapor
✔ One component acid-based curing system.
✔ Self-leveling.
✔ Excellent adhesion on various surfaces
✔ Colorless transparent or Black
✔ Good mechanical properties
✔ Heat resistant
✔ Resistant to weather influences and aging
✔ Permeable to gas and water vapor
✔ Transparent addition-curing silicone (platinum-cure), Shore A 40
✔ Excellent resistance to casting resins (polyurethane and epoxy)
✔ High tear strength > 25 N/mm for a long mold life
✔ Shrink-free curing (linear shrinkage ≤ 0.1 %)
✔ Mixing ratio 10 : 1, pot life approx. 80 minutes
✔ Slightly oily for better demolding
✔ Recommended operating temperature from -45 °C to +180 °C
✔ Neutral curing (Alkoxy), no acid
✔ Sprayable
✔ Good adhesion to many substrates without primer
✔ One component
✔ Solvent free
✔ Self-Leveling
✔ Very good flowability and self-deaeration
✔ Very low hardness (Shore A approx. 11)
✔ Good tear strength
✔ Excellent transfer characteristics for printing inks
✔ Antistatic finish
✔ Shore A 31 — middelhard, optimaal voor pad-printing
✔ Pot life 30 minuten, ontvormen na 5 uur
✔ Mengverhouding 9:1 (A:B) op gewicht
✔ Scheursterkte 30 N/mm — lange padlevensduur
✔ Krimpvrije uitharding bij kamertemperatuur
✔ Easy to process due to low viscosity
✔ Fast and shrink-free curing at room temperature
✔ Low Shore A hardness (approx. 25)
✔ High elongation, excellent tensile strength
✔ Excellent tear strength
✔ Cured rubber is transparent and colourless
