Professional Release Agents for Molds and Originals
🔧 Professional Release Agents for Molds and Originals Release agents facilitate the removal of a silicone mold from an original and from a casting in a silicone mold. Our carefully selected collection offers the perfect solution for every application. ✨ Why Release Agents Are Essential Silicone generally doesn't adhere unless...
This release spray is ideal for the treatment of surfaces which are (slightly) porous or whereby the possibility exists that silicones might adhere (mechanically or chemically). The spray can also be applied to the silicone mold itself to facilitate silicone...
Poly vinyl alcohol can be used to prevent cure inhibition from an otherwise "toxic" surface for addition curing silicones. If this poly vinyl alcohol is brushed on properly the poisoning material will not bleed through. PVA dissolves readily in water...
This wax based release spray is ideal for the treatment of surfaces which are (slightly) porous or whereby the possibility exists that silicones might adhere (mechanically or chemically). The spray can also be applied to the silicone mold itself to...
Description Talcum Powder is a multifunctional material that can be used for many purposes. The powder is ideal to eliminate the non-slipping character of silicone, but can also be used for a fine discharge between two layers of addition silicones....
SRA 6200 is a multi-purpose, medium duty, silicone mould release agent. It is based on silicones and has been formulated as a highly effective, multi-purpose release agent for most waxes, plastics and rubber moulding purposes. SRA 6200 provides a medium...
High carnauba wax content producing hard high gloss film – excellent for breaking in new molds Non-silicone - good tape adhesion for use where masking is required Effective in preventing/reducing pre-release on large tools, plugs & heavy laminates Excellent at...
Scope of application Helps loosen rubber and plastic parts. Works as a lubricant for plastic bearings, rubber parts, textiles and paper. Maintains rubber and plastic, for example as a cockpit spray. Protects against rust. Properties Transparent, water-repellent silicone layer. High...
Chemlease® 15 Sealer EZ is a high performance sealer developed to condition and seal mold surfaces, reduce mold porosity and act as a base for new or reconditioned molds. Benefits Reduces porosity problems. Provides an excellent base coat for all...
Chemlease® Mold Cleaner EZ is a special blend of solvents designed to dissolve and remove wax and dirt from composite molds. Ideal for preparing composite mold surfaces for the application of Chemlease® Mold Sealers and Releases. Also excellent for cleaning...
Chemlease® PMR-90 EZ is a rapid curing semi permanent mold release agent that provides multiple releases with minimal transfer to the molded part. Chemlease® PMR-90 EZ is the highest slip version of the Chemlease® PMR family; primarily for closed molding...
🔧 Professional Release Agents for Molds and Originals
Release agents facilitate the removal of a silicone mold from an original and from a casting in a silicone mold. Our carefully selected collection offers the perfect solution for every application.
✨ Why Release Agents Are Essential
Silicone generally doesn't adhere unless the surface is porous (unfinished wood, styrene, baked clay). In that case, you can use a pore sealer and/or release agent .
🎯 Important Applications:
Condensation silicones bond to addition and condensation silicones → Always use release agent
Addition silicone bonding to fresh addition silicone → Strongly recommended to use release agent
Polyurethane, epoxy and polyester bond strongly to many materials → Release agent protects your mold
🔬 Specialist Solutions
For absorbent surfaces: On highly absorbent surfaces, polyvinyl alcohol can be used as a release agent. This is especially helpful because it dissolves with plenty of water and therefore leaves little to no discoloration. This is used on marlstone, among other things.
✨ Finish & Gloss
The nature of the release agent determines whether the mold retains its gloss or not. Therefore, a good choice is important:
Buffable or wax-based release agents → Can often be buffed back to a shine
Powdered release agents → Provide a mattifying effect
🛡️ Protection & Benefits
✅ Material friendly - Protects both mold and original
✅ Professional results - Reliable release with every use
✅ Versatile - For different materials and applications
✅ Easy to use - For beginners and professionals
💡 Need Professional Advice?
Not sure which release agent is best for your specific project? Our experienced team is ready to advise you on the right choice for your application. Contact us for personalized advice!
