Silicone Addition Gel 840 Water Clear

Product form

Silicone Addition Gel 840 Water Clear

Light art by Hypar Collective, https://www.hyparcollective.nl/ The silicone gel 840 is a 2-component (Platinum) Poly-addition silicone which cures at room... Read more

In stock

€26,95€22,27 Incl. VATExcl. VAT


    Do you have a question about this product?

    • Everything available from stock
    • Buy from the specialist
    • Extensive internal laboratory
    • Pay later with Klarna!

    Size chart

    Light art by Hypar Collective, https://www.hyparcollective.nl/

    The silicone gel 840 is a 2-component (Platinum) Poly-addition silicone which cures at room temperature into a gel. These silicones exhibit, after mixing, good fluidity and turn crystal clear. This silicone gel will, over the course of time and at temperatures over 30°C, get a very faint yellowish glow.

    After the silicones have turned into a gel you can still puncture it to reach the measuring pins of the electronic components. If you work carefully the gel will close again sufficiently to shut out moisture.

    The very good fluidity provides a good self-deaerating property.

    • Very clear
    • Extremely iquid
    • Gel-like after hardening
    • Self-venting
    • Suitable for potting

    Technical data

    Mixing ratio in weight: A:B = 100:100
    Pot life/ processing time at 22°C: 80 minutes
    Functional crosslinking at 20°C: 24 hours
    Curing time at 20°C: 2 days
    Viscosity at 22°C: 125 cSt
    Color: transparant clear
    Penetration: 60 mm x 10 -1
    Dielectric value: 15 KV / mm
    Volume resistivity: 3X10 15 Ohm.cm
    Density: 0,94 g/cm³

    Note: Pot life / de-mould time is highly dependent on temperature! At a higher temperature, the processing time and de-mould time will be shorter.

    Processing

    The silicone gel 840 can be easily mixed by hand or by machine. Blend the A and B component carefully and in the indicated ratio (100 parts A and B in 100 parts by weight) together. Process the mixture within the pot life and de-mould only after it has cured complete. Alternatively, you can speed up the curing process by placing the whole mould in an oven. Please note that speeding up the process will leave more air bubbles trapped within the silicone casting.

    Extra information

    Trapping air bubbles can be prevented best by placing the silicone in a vacuum chamber immediately after mixing. To prevent air bubbles, stir the A and B component well but slowly without. The best way is to create a "figure 8" motion.

    This silicone gel will get a very faint yellowish haze at higher temperatures. For most potting and encapsulating purposes though this will not be a problem.

    Please note: This is an addition curing silicone. This type of silicones may experience cure inhibition when coming into contact with sulfer, nitrogen, amino groups and metl salts. If you are not certain that the products you use (including gloves, spatulas and cups) contain these ingredients, please do a little test first! These components are often found in many latex gloves, some platicines, glues, laquers, condensation curing silicones, silicone caulk, natural rubbers and 3D printing materials (mainly stereolithography). To use this gel on a poisening surface please use polyvynil alcohol as a protective layer in between.

    Durability 

    Provided that the silicone is in a sealed container and stored cool and frost-free, the shelf life is at least 1 year.

    Safety

    If you use silicone frequently we advise the use of gloves and to work in a properly ventilated area. For safety information see the safety data sheet.

    Further important safety information:

    H-CodeHazard Statements

    H315 - Causes skin irritation

    H319 - Causes serious eye irritation

    H361f - Suspected of damaging fertility

    H226 - Flammable liquid and vapour

    P-Code Precautionary Statements

    P201 - Obtain special instructions before use

    P202 - Do not handle until all safety precautions have been read and understood

    P210 - Keep away from heat/sparks/open flames/hot surfaces. - No smoking

    P281 - Use appropriate personal protective equipment

    P308 + P313 - AFTER (possible) exposure: Get medical advice/attention

    P370 + P378 - In case of fire: Use dry sodium carbonate for extinction

     

    Documentation

    Product information Silicone Addition Gel 840 Water Clear

    Login

    Forgot your password?

    Don't have an account yet?
    Create account

    Notify me!

    We will send you an email when this article is back in stock

    Notify me!

    Thank you, you will be notified when this item is back in stock.